ScopesAndAmmo.com Store Logo

+ Reply to Thread
Page 2 of 2 FirstFirst 12
Results 11 to 17 of 17

Thread: Your opinion of the "best" airgun available?

  1. #11
    Member
    Join Date
    Sat May 5 2012
    Posts
    220
    pistol Webley alecto .177 and .22

    Benjamin Discovery .177 and .22

    Hammerli AR20 FT .177

    a modded QB series airgun.
    Benjamin Discovery Mac1 modded <----- Ya Baby the new toy
    Webly Alecto .177
    QB79- with lots and lots of mods HPA <------ Go too AirGun for FT

  2. #12
    Senior Member Doc Sharptail's Avatar
    Join Date
    Sun Jan 1 2012
    Location
    Up The Escarpment
    Posts
    320
    Sean MP wrote:
    You can't beat a rolling block trigger for strength and consistency.
    I knew I had seen that trigger before :D
    Rear Sight; Is a perfect match to Feinwerkbau 300 rear aperture.
    I lusted after the 300-S. This was at a time when the old 52 International could be had for 900 and change.
    Front sight. Is an FWB 18mm. Anything fancy that fits the FWB pattern screws in here
    I doubt FWB would have taken the roll-pin mount shortcut, but that's just me. I've been known to be wrong before.



    Also in the package comes a CO2 bulk fill adapter.....that will run you another $60 with any other rifle
    Depends on where (and when?!) you buy. Archer still lists the bulk fill adapter as part of the package. The 2078 I just ordered in came without the adapter. I'm pretty sure this was done to keep the price point down.

    The platform will nearly instantly convert to a PCP
    Soonish to be determined. All I need is the pump :D



    Regards,

    Doc Sharptail
    Last edited by Doc Sharptail; Jan 18 2013 at 03:03 AM.
    "Ain't No Half Way"

    -S.R.V.

  3. #13
    Senior Member remtom1200's Avatar
    Join Date
    Tue Jan 3 2012
    Posts
    323
    Being the owner of two HPA modded QB78D's, a Hatsan AT44 10/22, and a room full of B18 platform springers it appears that budget type in general are the best for me. I contemplated buying an expensive pcp, most likely an Airforce Condor but! Higher price and still more money to spend on upgrades/ mods (cant help it must have upgrades!) so instead another QB78D is what I chose, and building it the way I like it. I am very lucky to have a creative mind , some skills, and some tools/machinery to make modifications and custom parts. So enough babbling I give the QB78D the best for modification and budget. I will have a condor yet btw.
    For every mile of road, there's two miles of ditch

  4. #14
    Moderator poil27's Avatar
    Join Date
    Sat Dec 31 2011
    Location
    not out enough
    Posts
    420
    for the moder it got to be the qb 78 family.easy to build what ever you like and going as crasy as you like whit it

    out of the box it has to be the at44. and/or the cz 200 s

    baikal izh 60 if it where the same price it was a couple of years ago.

  5. #15
    Member
    Join Date
    Tue Aug 28 2012
    Posts
    85
    Quote Originally Posted by Doc Sharptail View Post



    Depends on where (and when?!) you buy. Archer still lists the bulk fill adapter as part of the package. The 2078 I just ordered in came without the adapter. I'm pretty sure this was done to keep the price point down.


    Does the AR2078 from Scopes and Ammo come with the bulk fill adapter?

  6. #16
    Administrator AirGunEric's Avatar
    Join Date
    Sat Dec 3 2011
    Location
    Somewhere Out There
    Posts
    1,295
    Quote Originally Posted by Doc Sharptail View Post
    Archer still lists the bulk fill adapter as part of the package. The 2078 I just ordered in came without the adapter. I'm pretty sure this was done to keep the price point down.
    It's either old stock units, or he's adding the adapter (it is available from the factory as a separate part). I don't track Archer's prices, so it's entirely possible he raised the price $30.00 and put the adapter in- i.e. no choice for the customer. I was a bit surprised when our first shipment of the rifles came in with no adapters- seems the factory decided to do this sometime between when they told the old US importer he was "out" and they purchased S/R-Beeman.
    I'd say I care- but I'd probably be lying...


  7. #17
    Senior Member SeanMP's Avatar
    Join Date
    Thu Dec 22 2011
    Location
    Just south of "Out There"
    Posts
    911
    Quote Originally Posted by Doc Sharptail View Post
    I doubt FWB would have taken the roll-pin mount shortcut, but that's just me. I've been known to be wrong before.
    Doc Sharptail
    Ya that part ticks me off too...ya almost had it perfect fellas. But at least the tunnel is right.
    Sean

+ Reply to Thread

Similar Threads

  1. Update- links to "other" forum will be allowed...
    By AirGunEric in forum Forum Announcements and Questions
    Replies: 8
    Last Post: Jun 29 2013, 07:51 PM
  2. Funny story, or "how we get screwed in Canada"...
    By AirGunEric in forum General Airgun Questions
    Replies: 13
    Last Post: Jun 03 2012, 09:03 PM
  3. Just posting this as a "general note" as a result of a recent issue...
    By AirGunEric in forum Buyer/Seller Feedback
    Replies: 2
    Last Post: Feb 06 2012, 04:22 PM
  4. Doesn't really qualify as "Craftsmanship"- but it was my "first" airgun (1077) mod...
    By AirGunEric in forum Customization and Craftsmanship
    Replies: 11
    Last Post: Feb 02 2012, 04:02 PM
  5. QB78D Laminate Stock "before" and "after" from Microfit.
    By Merlyn in forum Customization and Craftsmanship
    Replies: 6
    Last Post: Jan 31 2012, 08:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts