ScopesAndAmmo.com Store Logo

+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: New Benjamin (Crosman) Underlever...MAV77

  1. #1
    Administrator AirGunEric's Avatar
    Join Date
    Sat Dec 3 2011
    Location
    Somewhere Out There
    Posts
    1,295

    New Benjamin (Crosman) Underlever...MAV77

    And just to state it up-front, it is nothing like the Chinese B3/B4 POS- it is a solid piece, but may have some teething problems (like a safety that got stuck, "on safe", that neither myself nor two Crosman reps could get unstuck without tools).

    The MAV77, listed at 1100fps, only available in .177 (which means, as we can probably all estimate, using a proper 7.9gr pellet likely means around 850fps).

    MAV77_1.jpg MAV77_2.jpg MAV77_3.jpg


    MAV77_4.jpg MAV77_5.jpg
    I'd say I care- but I'd probably be lying...


  2. #2
    Moderator poil27's Avatar
    Join Date
    Sat Dec 31 2011
    Location
    not out enough
    Posts
    420
    looks sharp

  3. #3
    Administrator AirGunEric's Avatar
    Join Date
    Sat Dec 3 2011
    Location
    Somewhere Out There
    Posts
    1,295
    It was a bit stiff to cock- but I believe this will get better as it breaks-in. The stock is not one of Benjamin's finest- but it was lacking the usual checkering- so I am thinking it may have only been put on this unit so it wasn't just the action sitting on a rack.
    I'd say I care- but I'd probably be lying...


  4. #4
    Moderator poil27's Avatar
    Join Date
    Sat Dec 31 2011
    Location
    not out enough
    Posts
    420
    ok benj did use bether stock than this one but the buesness end of the gun looks good may be a good subtitute to the hw 97 (may be not)

  5. #5
    Administrator AirGunEric's Avatar
    Join Date
    Sat Dec 3 2011
    Location
    Somewhere Out There
    Posts
    1,295
    What you can't see in the pictures is the thickness of the loading door/gate- it is thick (as in a half-inch of steel around the barrel on all sides) and the gate is held open by a lock-lever on the side so no one can get a finger snapped off. But, it was not a very "light" rifle as a result.
    I'd say I care- but I'd probably be lying...


  6. #6
    Moderator poil27's Avatar
    Join Date
    Sat Dec 31 2011
    Location
    not out enough
    Posts
    420
    i can understand that ... aluminium would have been a good idea

  7. #7
    Administrator AirGunEric's Avatar
    Join Date
    Sat Dec 3 2011
    Location
    Somewhere Out There
    Posts
    1,295
    For the loading door/gate that would have been a much better idea- maybe someday someone at Crosman will think of this...
    I'd say I care- but I'd probably be lying...


  8. #8
    Member Dukemeister's Avatar
    Join Date
    Sat Dec 31 2011
    Location
    Kingston, Ontario
    Posts
    177
    One of the big entrys this shot show for sure, it's all over the US forums, and UK, here as well. It's a BAM B40 with tweaks, supposedly for retail March, at SRP of $350 (meaning $300 retail). The Crosword tweet said up to 915 fps... lemme see if I can find the link...
    http://www.crosman.com/croswords/?p=2287
    there ya go. (later that day Crosman tweeted the SRP at $350 - there was a lot of complaint at $530... could have been a transpose I guess, but $350 it is). The B40 is an old TX200 copy, BAM have replaced it? with a B41, and the MAV77 may be an upgraded or rebadged B41 from the miriad posts I have read on this in the past 2 days.... I would buy one at $300 - with a basic 3-9x32 Centrepoint scope BTW (like the Nitro Venom X series - I have one it's OK scope, definitely not like on the Benji Classic and Trail AW - those are nice scopes). I'm sorta not impressed, the long awaited Browning Leverage looks to me to be a better value gun, but just guessing (Leverage has 3-9x40 AO scope and weaver rail, and is listed at $225 or so, not yet available of course).
    Member, Limestone Beekeepers Guild
    Duke ))))----//----------==

  9. #9
    Moderator
    Join Date
    Sun Jan 1 2012
    Posts
    51
    Any word on a detuned model? I really should get my PAL

  10. #10
    Member
    Join Date
    Sun Jan 1 2012
    Location
    Southern Ontario
    Posts
    87
    Any talk of a .22 tuned/detuned version?

+ Reply to Thread

Similar Threads

  1. Benjamin classic .22 with a new lense
    By chronic in forum Airgun Picture Gallery
    Replies: 20
    Last Post: Jan 18 2012, 08:39 PM
  2. Lowly Benjamin Legacy, Converted...
    By AirGunEric in forum Airgun Picture Gallery
    Replies: 3
    Last Post: Jan 01 2012, 11:29 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts